Fuse vs circuit breaker
- 4liters
- PHD in Yakology.
- Posts: 2140
- Joined: 02 Jun 2015, 10:55
- kayak: Native Watercraft Slayer 13, Stealth Fisha 500
- Real Name: Ian
Fuse vs circuit breaker
I have recently got my hands on a Lowrance Elite 5 HDI and in the instructions it says to use a 3 amp fuse. I was wondering if that could be replaced with a 3 amp circuit breaker and if so which one should I get?
- Franko
- Lord of the fish
- Posts: 1233
- Joined: 18 Jan 2015, 01:45
- kayak: Dune AI, stealth Supalite X
- Real Name: Frank
- Location: Sunbury
Re: Fuse vs circuit breaker
Something water proof to slow corrosion, not sure if you could get 3 amp breakers
- 4liters
- PHD in Yakology.
- Posts: 2140
- Joined: 02 Jun 2015, 10:55
- kayak: Native Watercraft Slayer 13, Stealth Fisha 500
- Real Name: Ian
Re: Fuse vs circuit breaker
They definitely make them: https://www.jaycar.com.au/3-amp-circuit ... r/p/SF2252FRANKB wrote:Something water proof to slow corrosion, not sure if you could get 3 amp breakers
I just don't know enough about electronics to know if the features of this kind of breaker will do the same job of protecting the sounder and batteries that a fuse will. I do like the idea of just pushing a button to get it going again rather than having to replace the fuse (and remembering to carry spares)
- cheaterparts
- Needs a life (forum tragic)
- Posts: 5758
- Joined: 29 Mar 2010, 07:04
- kayak: Stealth Profisha 525 ---
- Real Name: Stephen-The Mud King
- Location: Cranbourne
Re: Fuse vs circuit breaker
as said Corrosion is all ways the biggest problem - you can get water proof fuse holders and probably not water proof beakers ( these fuse holders can get also wet inside ) but if you use a dielectric grease on the contact points where the fuse fits this will save most of the problem4liters wrote:They definitely make them: https://www.jaycar.com.au/3-amp-circuit ... r/p/SF2252FRANKB wrote:Something water proof to slow corrosion, not sure if you could get 3 amp breakers
I just don't know enough about electronics to know if the features of this kind of breaker will do the same job of protecting the sounder and batteries that a fuse will. I do like the idea of just pushing a button to get it going again rather than having to replace the fuse (and remembering to carry spares)
My kayak PBs
Gummy shark 128 Cm -- Elephant fish 85 Cm -- Snapper 91 Cm -- KG Whiting 49 Cm -- Flathead 55 Cm -- Garfish 47 Cm --Long tail Tuna 86 cm -- Silver Trevally 40 Cm -- Cobia 117 Cm -- snook 53 Cm -- Couta 71 Cm -- Squid 44 hood length
cheater
0402 208 657
Gummy shark 128 Cm -- Elephant fish 85 Cm -- Snapper 91 Cm -- KG Whiting 49 Cm -- Flathead 55 Cm -- Garfish 47 Cm --Long tail Tuna 86 cm -- Silver Trevally 40 Cm -- Cobia 117 Cm -- snook 53 Cm -- Couta 71 Cm -- Squid 44 hood length
cheater
0402 208 657
- Yako
- Lord of the fish
- Posts: 1322
- Joined: 10 Mar 2013, 15:37
- kayak: PA 14, A.I, Revo16 & 4.1 Ocean Kayak
- Real Name: Rich
Re: Fuse vs circuit breaker
Ive got inline fuse as the corrosion concerns me on a breaker in salt water. As cheater says a simple dialectic like no name brand petroleum jelly works well
John 3.16/17
- bunyip
- Square eyes
- Posts: 528
- Joined: 29 Jul 2016, 11:50
- kayak: Prowler 13 and Cole 23 floating bordello
- Real Name: Iain
- Location: Lang Lang
Re: Fuse vs circuit breaker
We use a few on the yacht and they are encapsulated in a silicon sheath so I can push the button if it trips, we just used heat shrink over the ends of the silicon tube and it is quite watertight.
The salt air is the biggest killer not water itself, well I suppose it is but indirect.
The salt air is the biggest killer not water itself, well I suppose it is but indirect.
- chrisw
- Square eyes
- Posts: 577
- Joined: 17 Dec 2016, 18:06
- kayak: Dune PA14
- Real Name: Chris
- Location: Werribee South
Re: Fuse vs circuit breaker
I have a 3 amp breaker on mine but left the fuse in place also. If you want to be really safe put in a 20 amp fuse and a 3 amp breaker. The breaker should trip before the fuse.4liters wrote:I have recently got my hands on a Lowrance Elite 5 HDI and in the instructions it says to use a 3 amp fuse. I was wondering if that could be replaced with a 3 amp circuit breaker and if so which one should I get?
I use Blue Sea Systems marine breakers (https://www.amazon.com/dp/B000MMDLQQ/) along with their rubber caps (https://www.amazon.com/dp/B000MMDLKW) in my switch panel:
That panel came with 15 amp breakers but I swapped them with the appropriate ones for each circuit.
I only have them in that box because I'm not sure where I'm going to permanently mount them. You could put a breaker directly in the hull pretty easily (just remember to add waterproofing to the back of the breaker as well - some goop or liquid electrical tape would do it).
I might even have a spare lying around; I certainly have some 15 amp ones but not sure about a 3A.
EDIT: I note C. H. Smith have them too, though not in 3A: http://www.chsmith.com.au/Products/Push ... eaker.html. You could probably safely use a 5A one though.
- 4liters
- PHD in Yakology.
- Posts: 2140
- Joined: 02 Jun 2015, 10:55
- kayak: Native Watercraft Slayer 13, Stealth Fisha 500
- Real Name: Ian
Re: Fuse vs circuit breaker
Thanks for the info guys
Do you have a picture of this silicone sheath? How do I go about making one or is it something you buy?bunyip wrote:We use a few on the yacht and they are encapsulated in a silicon sheath so I can push the button if it trips, we just used heat shrink over the ends of the silicon tube and it is quite watertight.
The salt air is the biggest killer not water itself, well I suppose it is but indirect.
- bunyip
- Square eyes
- Posts: 528
- Joined: 29 Jul 2016, 11:50
- kayak: Prowler 13 and Cole 23 floating bordello
- Real Name: Iain
- Location: Lang Lang
Re: Fuse vs circuit breaker
I haven't got a pic and the boat lives at Paynesville so I'm not going down until it warms up a bit but it was just a tube section of soft silicon that I acquired from a sparky, neoprene would most likely work as well and sealed with neoprene cement just don't have it too small so it restricts the button popping up.
Breakers I got were a bundle of leftovers I found on Gumtree, mixed bag of amps and got them for about $15 for about 50 of them, I gave a lot away but you get lucky sometimes.
Back to the tube, I think neoprene would be easier as you don't have to build up the wire to accept the heatshrink and if you have a bank of breakers it would be easier to fabricate.
Breakers I got were a bundle of leftovers I found on Gumtree, mixed bag of amps and got them for about $15 for about 50 of them, I gave a lot away but you get lucky sometimes.
Back to the tube, I think neoprene would be easier as you don't have to build up the wire to accept the heatshrink and if you have a bank of breakers it would be easier to fabricate.
- 4liters
- PHD in Yakology.
- Posts: 2140
- Joined: 02 Jun 2015, 10:55
- kayak: Native Watercraft Slayer 13, Stealth Fisha 500
- Real Name: Ian
Re: Fuse vs circuit breaker
It'll probably be just the one breaker as I don't plan on having any other electronics running off the same battery.
Which neoprene tube should I be getting? I didn't even know it came in anything other than wetsuits until a minute ago
Which neoprene tube should I be getting? I didn't even know it came in anything other than wetsuits until a minute ago